
Waterjet Cutting Materials: What It Cuts and How

Abrasive waterjet cutting can handle nearly any material a commercial project calls for: stainless steel, aluminum, brass, titanium, tool steel, stone, glass, ceramics and composites. It does this without heat, so the edge you get keeps the properties of the sheet you started with. Pure water, with no abrasive, is for soft materials such as foam, rubber, gaskets and food. If you are a restaurant owner, hotel manager, contractor or architect, the rule is short: metal means abrasive waterjet, and the cut quality depends on speed, pressure and how the part is programmed. Our Water Jet Cutting Service is run from our shop in Brooksville, Florida.
This guide covers which materials waterjet cuts, how the process works in plain terms, what to expect on stainless steel, and what to put in a request so the parts come out right the first time.
TL;DR
- Abrasive waterjet cuts hard materials, including tool steel up to 200 mm thick. Pure waterjet is for soft materials such as foam, rubber, textiles and food.
- The jet erodes material along a CNC-programmed path with no heat at the cutting zone, so there is no heat-affected zone, warping or hardening at the edge.
- On stainless steel, slower travel, correct pressure and the right standoff distance improve edge quality. Thick material may need more than one pass.
- Tolerances of ±0.005 in. are readily achievable in nearly all materials under 2 in. thick.
- Send a drawing file, the alloy and thickness, the finish you need and the quantity. That is enough to start a quote.
Table of Contents
- Which materials can waterjet cut?
- Pure waterjet vs. abrasive waterjet
- How the waterjet cutting process works
- Waterjet cutting stainless steel
- Why a cold cut matters in a commercial kitchen
- Choosing between waterjet and other cutting methods
- What to include when you request waterjet-cut parts
- Waterjet for countertops, sinks and cladding
- Our approach to waterjet work
- Perspective
- FAQ
- Sources
Which materials can waterjet cut?
The short answer is a very wide range. The longer answer depends on which kind of waterjet is used, because the two types do different work.
According to the Open University’s engineering guide, pure waterjet suits non-metallic materials and thin, soft metals such as aluminum, copper, lead and mild steel. The same guide lists plastics, composites, wood, paper, leather, fabric, food and ceramics among the materials the process handles. Adding abrasive extends the range to the hard materials a fabrication shop sees every day.
Here is how that looks in practice for commercial work.
| Material | Typical use in hospitality and commercial projects | Waterjet type |
|---|---|---|
| Stainless steel | Countertops, sink cutouts, tables, wall cladding, hood components | Abrasive |
| Aluminum, brass, copper | Trim, decorative panels, signage, fittings | Abrasive for thicker stock |
| Tool steel, titanium | Machine parts, specialty components | Abrasive |
| Stone, tile, glass | Inlays, backsplashes, feature walls | Abrasive |
| Composites and laminates | Panels, fixtures | Abrasive, with care |
| Gasket material, rubber, foam | Seals, gaskets, padding | Pure |
| Food | Portioning | Pure |
The IEEE Technology Navigator confirms the range at the hard end: abrasive waterjet cuts engineering materials including tool steel, with thicknesses up to 200 mm. It also reports use on titanium alloys, carbon-fiber composites, hardened tool steels and ceramics.
Materials that need extra care
A few materials are not a question of whether waterjet can cut them but of how they are handled. The Open University guide notes that laminated composites may delaminate, and that acrylics, polycarbonates and styrene cut poorly except in thin sheets. For those, the setup, such as how the piercing is done and how the sheet is held, makes the difference. If your design uses layered panels or plastics, tell us the exact product when you request a quote so the cut is planned around it.
Pure waterjet vs. abrasive waterjet
Both start the same way. A pump pressurizes water and forces it through a tiny jewel orifice. According to the IEEE Technology Navigator, that orifice is typically 0.1 to 0.4 mm across, and the jet leaving it can exceed 900 m/s.
Pure waterjet uses only that stream. It works on soft materials: textiles, rubber, foam, food, paper, wood composites and thin plastics. There is nothing hard in the jet, so it is gentle on the material.
Abrasive waterjet adds a fine abrasive, usually garnet, to the water in a mixing chamber just before the jet exits the nozzle. The water accelerates the particles, and the particles do the cutting. This is the version used for metal, stone, glass, ceramics and composites. If you are buying stainless steel parts, abrasive waterjet is the process in question.

As a practical matter, a metal job will almost never be pure waterjet. When a shop says “waterjet” in the context of steel, it means the abrasive kind.
How the waterjet cutting process works
The process is easier to follow as a sequence.
- Pressurize. A high-pressure pump raises the water to extreme pressure. The IEEE reports typical operating pressures of 200 to 600 MPa. The Open University guide gives a broader working range of 70 to 415 MPa, which reflects different machine types.
- Form the jet. The water passes through a jewel orifice, which converts pressure into a narrow, very fast stream.
- Add abrasive. In an abrasive system, garnet is drawn into the stream in a mixing chamber and accelerated through the nozzle.
- Follow the path. A CNC controller moves the cutting head along the programmed outline from your drawing file. The jet erodes and fractures the material along that path without generating heat at the cutting zone.
- Catch the spent jet. The water and abrasive are absorbed below the sheet, which sits on a support while the head moves above it.
Because the cut is mechanical erosion, the shape you can produce is limited mainly by the drawing and the nozzle size, not by a die or a tool. Interior cutouts, tight curves and one-off profiles are programmed rather than tooled. That is why waterjet fits custom work, where each part may differ.
Waterjet cutting stainless steel
Stainless steel is the material most commercial kitchens are built around: prep tables, countertops, sinks, hoods, splashbacks and wall cladding. Waterjet suits it for a straightforward reason. The cut produces no heat-affected zone, so the metal at the edge is the same metal as the rest of the sheet.
The Fabricator reports that waterjet cutting leaves no physical, thermal or chemical alteration in the material and works on ferrous and nonferrous metals, brittle and ductile materials, and composites. For a kitchen surface that will be cleaned constantly and sit next to food, an edge that has not been thermally altered is a sensible starting point.

What affects cut quality and usable thickness
The IEEE lists the main variables behind kerf width (the width of the cut), surface roughness and depth of cut: pump pressure, abrasive flow rate, standoff distance, traverse speed and orifice characteristics. In plain terms:
- Pressure. Higher pressure improves penetration and edge quality, but it takes more power, according to the Open University guide.
- Speed. Slower travel improves quality. Thick material may need multiple passes.
- Standoff distance. This is the gap between the nozzle and the sheet. The same guide gives about 5 mm as typical, and notes that a greater gap increases noise while reducing penetration.
- Abrasive flow. More abrasive generally means more cutting power, within limits set by the nozzle.
The practical reading is that edge quality is something you choose. A part that will be hidden behind a panel can be cut faster. A visible edge, such as a feature wall or an exposed table edge, can be cut slower for a smoother finish. When you request a quote, say which edges will be seen.
Tolerances you can plan around
For most hospitality fabrication, dimensional accuracy matters more than anything else, because parts have to fit into a cabinet run, a wall opening or a sink cutout. The Fabricator states that ±0.005 in. is readily achievable in nearly all materials under 2 in. thick. For sheet-based kitchen work, nearly everything falls well inside that range.
Why a cold cut matters in a commercial kitchen
Heat changes metal. It can warp thin sheet, discolor stainless, and leave an edge that needs more finishing before it is safe and clean. Because waterjet is a cold process, the heat-related effects are not part of the cut. The IEEE notes that waterjet avoids heat-affected zones, warping and residual stresses.
For the people who buy kitchen metal, that translates into a few concrete benefits:
- Flat parts. Thin stainless panels for wall cladding stay flat.
- Consistent material. The metal at the edge keeps the properties of the sheet.
- Less rework. Fewer distortions mean parts arrive at the install closer to finished.
- Complex shapes. Cutouts for sinks, faucets, drains and equipment can be programmed to the exact dimensions of the fixtures going in.
Choosing between waterjet and other cutting methods
A fabrication shop usually has more than one way to cut a part, and the right one depends on the material, thickness and edge requirement. Waterjet, fiber laser and plasma overlap, but each has a sweet spot.
| Need | Often the best fit |
|---|---|
| Thick plate, stone, glass, composites, no heat at the edge | Waterjet |
| Thin to medium sheet, fine detail, fast production | Fiber laser |
| Thicker steel plate where speed matters | Plasma |
| Straight cuts on sheet | Shearing |
We run several of these under one roof. Our site lists fiber laser, plasma and shear cutting alongside the waterjet service, so the process can be matched to your part instead of the part being bent to fit one machine. If you are unsure which suits your drawing, send us the file and the use case.
What to include when you request waterjet-cut parts
The fastest way to a correct quote is a complete request. Here is what we need.
- A drawing file. A DXF or DWG file for flat parts is ideal. A dimensioned PDF also works as a start.
- The material and alloy. For stainless, name the grade your spec calls for, such as 304 or 316. If you need raw material supplied, see our raw metal sales.
- Thickness. Gauge or decimal inches.
- Quantity. One prototype, a set for one kitchen, or repeat production.
- Edge and finish. Which edges are visible, and whether the parts go on to welding, bending or polishing.
- Where it goes. A countertop, hood, wall panel or enclosure tells us what the part has to do.
If the parts are one piece of a larger assembly, such as a counter with a sink and a backsplash, it can help to have the cutting and the build done in one place. That is where custom fabrication and welding comes in, so the cut parts go straight to forming and assembly.
Waterjet for countertops, sinks and cladding
To make this concrete, here are the typical places a kitchen or hotel project uses waterjet-cut parts.
- Countertops. Sink, faucet and drain openings cut to the equipment’s dimensions.
- Sinks and tables. Drain and fitting cutouts, undershelf details and custom shapes.
- Wall cladding. Panels with outlet, vent and switch openings, or decorative patterns for a front-of-house feature.
- Hood components. Flat parts for custom commercial exhaust hoods, cut to the room’s dimensions.
- Enclosures. Heavy metal enclosures with ports, vents and access openings.
In each case, the benefit is the same: a CNC path from your drawing, repeated exactly, so the second panel matches the first.
Our approach to waterjet work
DAY METAL LLC is a custom metalwork shop in Brooksville, Florida, serving commercial kitchens, restaurants and hotels, with more than 60 years of combined experience on the team. Our products are manufactured locally. Our CNC machining and cutting services, including water jet, fiber laser, plasma and milling, sit alongside welding and finished fabrication. You can see the full list on our services page.
If you have a drawing, a spec or just an idea for a stainless steel piece, send it to us through our website. The cutting, the fabrication and the assembly are handled by one local team.

Perspective
When we look at a waterjet job, we start with what the part has to do in the room, not with the machine. A countertop in a hotel kitchen lives under constant washing, heavy loads and tight clearances. A cold cut that leaves the stainless as it came off the coil is a sound foundation for that.
Our advantage is that the cutting, the CNC work, the welding and the finishing happen at one Brooksville shop. That means a drawing change does not have to travel between vendors, and the person who programs the cut knows what the welder and the installer need next. We build for restaurants, hotels and commercial facilities, so we think about cleaning, durability and fit from the first line on the drawing.
Our advice to architects and contractors is to bring us in early. Tell us the alloy, the visible edges and the equipment going in. Those three details decide the cutting method and the quality setting, and they are much cheaper to settle on paper than on site.
the author
FAQ
What materials can waterjet not cut?
Very few materials are off the table for abrasive waterjet. The practical limits are about handling rather than cutting: laminated composites can delaminate, and acrylics, polycarbonates and styrene cut poorly except in thin sheets, according to the Open University guide. Tell us the exact material and we plan the cut around it.
Can waterjet cut stainless steel?
Yes. Abrasive waterjet cuts stainless steel, and because it is a cold process it leaves no heat-affected zone at the edge. The finish and the usable thickness depend on pressure, travel speed, abrasive flow and standoff distance. Give us the grade and thickness and we will set the cut for the edge you need.
How does waterjet cutting work?
A pump pressurizes water, which is forced through a jewel orifice to form a fast, narrow jet. For metal, garnet abrasive is added in a mixing chamber and accelerated by the water. A CNC controller moves the head along your programmed path, and the jet erodes the material without heat.
What is the difference between pure and abrasive waterjet?
Pure waterjet uses water alone and is for soft materials such as foam, rubber, textiles and food. Abrasive waterjet adds garnet or another abrasive and cuts hard materials such as metals, stone, ceramics and composites. Stainless steel work is done with the abrasive type.
How accurate is waterjet cutting?
The Fabricator reports that ±0.005 in. is readily achievable in nearly all materials under 2 in. thick. Slower cutting generally improves edge quality, so visible edges can be cut at a finer setting.
Sources
- Water jet cutting (Hydrodynamic cutting), OpenLearn, The Open University
- Water jet cutting, IEEE Technology Navigator
- Determining what’s fact or fiction in waterjet cutting, The Fabricator
