The Day Metal Journal

Sheet Metal Welding Services for Commercial Kitchens

14 min read
Welder joining a stainless commercial sink rim

Sheet Metal Welding Services for Commercial Kitchens

Welder joining a stainless commercial sink rim

Good sheet metal welding for a commercial kitchen comes down to three decisions: the process (TIG for visible and food-contact seams), the finish (smooth, continuous, crevice-free welds where food touches the steel) and a fabricator who controls heat, cutting and finishing under one roof. Get those right and your countertops, sinks, tables and hoods stay strong, clean and inspector-friendly for years. We build this kind of work in Brooksville, Florida, and this guide explains what to specify, in plain terms, whether you run a restaurant, manage a hotel, build for clients or draw the plans.

Day-metal
day-metal.com
Build Cleaner, Longer-Lasting Kitchen Metalwork
Day-metal fabricates custom stainless steel countertops and sinks, with CNC capabilities for commercial kitchens in Brooksville, Florida.
Visit

TL;DR

  • For stainless sheet in kitchens, TIG (GTAW) is the process to specify on visible and food-contact seams. MIG is faster but leaves a larger bead that is harder to polish.
  • Food-contact welds should be continuous, full penetration, free of pits and crevices, and finished to about 32 microinches Ra (0.8 µm) under 3-A guidance.
  • Heat is the enemy: too much causes distortion, heat tint and lost corrosion resistance. Cleaning and passivation after welding restore the surface.
  • Non-contact welds do not need a mirror polish, but they must still be smooth and cleanable.
  • Put welding, cutting and forming with one local shop and you cut handoffs, fit-up errors and delays.

Table of Contents

What sheet metal welding services actually cover

Sheet metal welding joins thin metal, usually under about 1/8 inch, into a single permanent part. According to TWI, a welding and joining research institute, welding fuses two pieces with heat, and when done correctly the bond is extremely strong.

In a commercial kitchen project, the welding service is rarely a stand-alone task. It sits inside a chain: cutting the flat sheet, bending it on a press brake, welding the seams, finishing the welds, then assembling and installing. Typical welded items include:

  • stainless countertops with integral backsplashes and welded-in sinks
  • worktables with undershelves and legs
  • commercial exhaust hoods and wall cladding
  • heavy enclosures for equipment

We cover this chain from our Brooksville shop: custom fabrication and welding, brake forming and bending, and CNC cutting by fiber laser, plasma and water jet. If you want a broader primer on how the pieces fit together, our page on what metal fabrication and welding involves walks through it.

Which welding process fits which job

Stainless steel can be welded by many methods. Outokumpu, a stainless steel producer, groups them into fusion methods, where the edges are heated with or without filler metal, and pressure methods, where clean surfaces are pressed together to form a metallic bond. The American Welding Society’s 2019 guide to austenitic stainless names stick (SMAW), TIG (GTAW), MIG (GMAW), submerged arc and flux-cored welding as the most commonly used processes.

For sheet, three matter most to you as a buyer.

Process Best for Trade-off
TIG (GTAW) Thin sheet, visible seams, food-contact and sanitary joints Slower, but a smaller bead that polishes more easily
MIG (GMAW) Thicker sheet and hidden structural joints where speed matters Larger bead, more spatter, more cleanup
Spot / resistance welding Overlapping panels in high-volume assemblies Suits repeated production, less so one-off custom pieces

The ranges in the table follow a 2026 stainless sheet welding guide: TIG suits roughly 0.010" to 0.125" sheet and visible or sanitary seams, MIG suits 0.060" and up where speed matters more than looks, and spot welding handles 0.020" to 0.120" overlapping panels. The 3-A training material on fabrication makes the same point from the hygiene side: TIG is slower but easier to polish, MIG is faster but leaves a larger bead that is harder to polish.

Laser welding also exists. Miller’s comparison of laser, TIG and MIG notes that laser’s small melt pool leaves only a faint heat tint and no spatter, while TIG avoids spatter but leaves tint to remove, and MIG needs mechanical cleanup. For most custom kitchen work, though, the practical question is TIG or MIG, and the answer follows where the weld sits.

Metalworker welding a component amid bright flying sparks

A simple rule of thumb

If food, water or a cleaning cloth touches the weld, ask for TIG. If the weld is hidden inside a frame or under a shelf and strength is the goal, MIG can be a sensible choice. A good fabricator will tell you which seam gets which process before work starts.

Welder fabricating a steel frame in a workshop

What makes a weld sanitary

A sanitary weld is one that leaves nowhere for soil and bacteria to hide and that you can clean fully with ordinary kitchen routines. Two bodies are worth knowing.

The first is the FDA Food Code, the model rulebook most US health departments build on. The 2022 edition defines a food-contact surface as one that normally touches food, or one from which food may drain, drip or splash onto food or another food-contact surface. That wording matters: a countertop edge, a sink rim and a backsplash seam can all qualify, not just the prep surface. The same document defines a smooth surface as free of pits and inclusions, with cleanability equal to or better than No. 3 stainless steel (100 grit).

The second is 3-A, a hygienic-design standards body. Its guidance says product-contact surfaces, welded joints included, should be at least as smooth as 32 microinches Ra (0.8 micrometres) and free of pits, folds, cracks, crevices and misalignments. Welds should be continuous, with no skip or stitch welds. Ra is simply a measure of average surface roughness: the lower the number, the smoother the steel.

Under the AWS D18.1 sanitary welding specification, as explained in a 3-A presentation on hygienic welding, welds that do not meet the visual standard must be finished to a maximum of 32 microinch Ra. Welds must be full penetration, with no cracks, undercut, crevices or embedded or protruding material. The same source explains why TIG is preferred for sanitary welds: it uses no flux, so there is no risk of slag or flux inclusions that become contamination harbors.

Contact versus non-contact welds

Not every weld needs the same treatment. A 3-A presentation on hygienic materials says welds on non-product-contact surfaces need not be ground or polished, provided exposed surfaces are relatively smooth and free of soil-trapping pockets and crevices. Practically, that means:

  • Work surface, sink bowl, splash zones: continuous TIG weld, ground flush and finished smooth.
  • Underside, frame, enclosure interior: a clean, full-penetration weld that is smooth enough to wipe down, without paying for a mirror finish nobody sees.

Specifying this split on your drawings keeps cost where it protects you and out of where it does not.

Certified equipment and the health inspector

If you buy catalog equipment, the FDA notes that the Food Code recognizes equipment certified to an ANSI-accredited standard, with NSF/ANSI 2 for food equipment and NSF/ANSI 51 for food-equipment materials among those named. The 2022 Food Code changes clarified that equipment certified to an appropriate American National Standard is deemed to comply with the equipment sanitation provisions in Parts 4-1 and 4-2. Custom fabrication is reviewed locally, so confirm requirements with your county or state plan reviewer early, before drawings are final. That is a step the law gives to the authority, and a fabricator who works with kitchens regularly will build the drawings around it.

Why heat control decides quality

Stainless steel conducts heat poorly, so heat stays where you put it. The Southern African Stainless Steel Development Association’s welding handbook notes that austenitic grades (the 304 and 316 families common in kitchens) are prone to distortion because heat lingers near the heat-affected zone. It recommends minimum heat input for the thickness and, on butt welds in thicker sections, welding the deeper side first to limit distortion.

What you see on a finished piece:

  • Warping. A countertop that waves along a seam holds water and looks cheap. Controlled heat, good clamping and sequenced welds prevent it.
  • Heat tint. The straw-to-blue discoloration beside a weld. As the Miller comparison above says, TIG leaves tint that must be removed for a bright finish.
  • Lost corrosion resistance. Stainless resists rust through a thin chromium oxide film. Welding heat damages it locally.

Shielding gas matters too. According to a 2025 stainless welding best-practices article, TIG on stainless almost always uses 100% argon, with argon or nitrogen-argon blends for back purging on austenitic grades to prevent oxidation on the root side. MIG commonly runs 98% argon and 2% CO₂, and higher CO₂ improves penetration but can pick up carbon and reduce corrosion resistance in low-carbon grades such as 304L and 316L. You do not need to specify gas on a purchase order, but it explains why the same weld can look and last differently between shops.

Alleima, a stainless producer, lists clean preparation, suitable filler, suitable parameters and post-weld cleaning as the steps toward a successful stainless weld. Clean preparation also means keeping carbon steel dust away from stainless, a point we return to below.

Weld polishing and finishing, step by step

Polishing is where a good weld becomes a sanitary one. The sequence below follows a 2026 sanitary weld polishing guide, written for pipe joints but equally applicable to the logic of sheet seams.

  1. Grind the crown flush. Start with about 80 grit to remove the weld bead and discoloration until the seam is level with the parent metal.
  2. Step up the grits. Move through 120, 180, 240 and 320 grit (or a fine non-woven pad), blending out each scratch pattern and changing direction about 90 degrees between grits.
  3. Match the surrounding finish. The weld should blend into the sheet’s grain so it does not read as a repair, and so there are no low spots to trap soil.
  4. Use stainless-only abrasives. Wheels or pads that have touched carbon steel can embed iron that later rusts.
  5. Passivate. Apply a citric passivation solution or a pickling paste to the weld and heat-affected zone, then rinse with clean water. This restores the protective chromium oxide film; skipped, the surface can flash-rust in service.

The Alleima guide adds context on the wider options: it recommends removing the chromium-depleted zone after welding, calls electrolytic polishing the best method but slow and expensive, says pickling can give a smooth surface with optimum corrosion resistance, and notes that for mechanical polishing the finer the grit, the better the corrosion resistance.

How to judge a finished weld

You do not need instruments to spot trouble. Run a clean glove or a fingertip along the seam. You should feel no ridge, pinhole or step, and see no dark pits, cracks or leftover tint. In a sink, check the corners where bowl meets rim. On a countertop, sight along the seam under raking light to check for waviness. For documentation-heavy projects, 3-A’s explanation of equipment verification lists what a quality program looks at: material certifications, weld quality, surface finish, corner radii, cleaning method, drainability and inspection access. Hygienic fabrication is a system, not just a shiny surface.

Common stainless welding defects and what causes them

Most defects trace back to heat, contamination or poor fit-up. These are the ones that show up in a kitchen.

Defect What you see Usual cause Why it matters in a kitchen
Distortion Waves or bowing near seams Excess heat input, poor clamping Pooling water, uneven surfaces
Heat tint Gold, brown or blue bands Heat plus inadequate shielding Reduced corrosion resistance until removed
Spatter Beads of metal stuck beside the weld Common with MIG Rough spots that trap soil
Pits and porosity Small holes in the bead Contamination, gas coverage problems Crevices for bacteria
Undercut or crevices Groove along the weld edge Technique or parameters Fails the sanitary criteria
Skip or stitch welds Gaps between weld sections Cost-cutting on seams Gaps are not permitted on food-contact joints under 3-A guidance

We cover prevention in more depth on our page about how to avoid common welding defects. The short version: clean material, controlled heat, correct filler and a finishing step that is planned from the start, not an afterthought.

Designing for a clean weld

Many weld problems begin in the drawing. A few habits save money and rework.

  • Specify the material grade. 304 is the usual choice for most kitchen surfaces; 316 for chloride-heavy or harsh-chemical areas such as some dish and wash zones. Ask your fabricator which grade fits your cleaning chemicals.
  • Mark contact and non-contact seams. It tells the shop where to grind and polish, and where a clean wipe-ready weld is enough.
  • Prefer continuous seams. Avoid stitch welds where anything can drain or splash.
  • Use formed radii instead of sharp corners. A bent coved corner needs no weld at all, which is why brake forming and welding are planned together. See our note on brake metal forming and bending.
  • Start with clean cuts. Precise CNC cutting produces parts that fit tightly, and tight joints weld with less heat and less filler. Our guide to laser cutting stainless steel explains what affects edge quality.

If your project is part of a larger buildout, coordinate the steel with the other trades. A general contractor handling commercial construction services such as interior renovations and tenant improvements will want hood, wall cladding and counter dimensions confirmed before walls close, and a shop that cuts, bends and welds in-house can revise a drawing quickly.

Why one local shop beats a chain of vendors

Splitting cutting, bending, welding and finishing across several vendors multiplies the places a part can arrive out of tolerance. Each handoff adds shipping time and an argument over who owns the error. When one shop does the work, a seam that does not fit is fixed at the bench, not litigated by email.

That is the idea behind how we work. Every product we make is manufactured locally in Brooksville, Florida, using CNC machining and the custom engineering your drawing needs, and our team brings more than 60 years of combined experience. For you, that translates into one point of contact for countertops, sinks, tables, hoods, wall cladding and enclosures, and fewer surprises between drawing and installation.

What we believe about welded stainless

A weld is the part of a kitchen fixture that you remember. Nobody notices a flat countertop for ten years, but everyone notices a seam that has pitted, stained or trapped grime. That is why we treat welding as part of the design, not as the last operation on the shop floor.

Our approach is to engineer the part around the weld: cut it precisely on CNC equipment so edges meet cleanly, form the bends so fewer seams are needed, and weld what remains with the hygiene of the finished surface in mind. We build handcrafted, long-lasting solutions because restaurants, hotels and healthcare kitchens run hard, and a fixture that has to be replaced early costs far more than one built correctly the first time.

Because the whole job is made here in Florida, you can talk to the people who cut, bend and weld your piece. We think that personal approach is the best way to match a fixture to the way your kitchen really works.

the author

Get your kitchen metalwork built in one place

If you are planning custom stainless countertops, premium sinks, commercial exhaust hoods, wall cladding, stainless tables or heavy enclosures, we make them locally and can handle the cutting, welding and assembly together. Send us your drawings or dimensions and tell us where each surface sits in the kitchen. You can see everything we offer on our services page or start from Day Metal’s home page.

Day-metal

We serve restaurants, hotels, healthcare, education and other commercial settings, and we also supply raw metal material for shops that fabricate their own parts.

FAQ

Which welding is used for sheet metal?

TIG (GTAW) and MIG (GMAW) are the two most common for sheet, with spot welding used for high-volume overlapping panels. TIG gives the cleanest, most polishable seam, so it is the usual pick for visible and food-contact joints. MIG suits thicker or hidden structural joints where speed matters.

Do all welds on kitchen equipment need to be polished?

No. Welds on food-contact surfaces need a smooth, crevice-free finish, around 32 microinches Ra under 3-A guidance. Non-contact welds do not have to be ground or polished, but the surface should still be relatively smooth and free of pockets that trap soil.

What is passivation and why does it follow polishing?

Passivation restores the thin chromium oxide film that protects stainless steel from rust. After polishing, the weld and the heat-affected area are treated with a citric solution or pickling paste and rinsed with clean water. Skipped, a weld can flash-rust or corrode in service.

What does food-grade stainless welding mean?

It means the weld is continuous, fully penetrated and finished so that it has no pits, cracks or crevices where food residue can collect, and it can be cleaned fully. In the US, the FDA Food Code and 3-A guidance describe the surface requirements, and your local health department reviews the finished kitchen.

What should I send a fabricator to get a welding quote?

Send dimensioned drawings, the stainless grade you want, the finish, and a note on which surfaces touch food or splash. Add quantities, the installation site and any deadlines. Clear contact-versus-non-contact marking lets the shop plan the finishing work accurately.

Sources

Have a Project in Mind?

Bring your questions and specifications to the Day Metal team.

Discuss Your Project