The Day Metal Journal

CNC Machining Tolerances: What to Specify and Why

13 min read
Geometric block between two tolerance planes

CNC Machining Tolerances: What to Specify and Why

Geometric block between two tolerance planes

A CNC machining tolerance is the amount a finished dimension is allowed to vary from the number on the drawing. Most general CNC work is held to about ±0.005 inch (±0.13 mm) as a baseline, and you pay more as you ask for less variation. The best specification is the loosest one that still lets the part do its job, and the best way to get there is to talk through the drawing with the shop that will cut it. At Day Metal in Brooksville, Florida, we run CNC machining, fiber laser, plasma and water jet cutting, milling and welding under one roof, so a tolerance question gets answered by the people who will make the part.

This guide is written for the people who buy and specify custom metalwork: restaurant owners, hotel managers, contractors and architects. You don’t need to be a machinist. You need to know what the numbers on a drawing mean, which ones drive cost, and which ones you can safely relax.

Day-metal
Custom Metalwork, Made with Precision
Explore custom CNC-fabricated metalwork for commercial kitchens, made locally in Brooksville with attention to precision and durability.

TL;DR

  • A tolerance is the total allowed variation in a size. General CNC work is typically quoted around ±0.005 in (±0.13 mm); tighter than that is a deliberate, costlier choice.
  • Tolerances appear on a drawing as direct limits on a dimension, a general note covering everything else, or geometric symbols that control shape and position.
  • Tight tolerances belong on features that mate with other parts, such as bearing seats, locating holes and sealing faces. Cosmetic edges and clearance holes do not need them.
  • Over-specifying adds machining time and scrap. Specify only as close as the function requires, and make sure the number can actually be measured.
  • Send us the drawing before it is final. We can tell you which dimensions matter and which can be relaxed.

Table of Contents

What a tolerance actually is

No machine cuts exactly 2.000 inches every time. Tools wear, metal moves with heat, fixtures flex and measuring tools have their own error. A tolerance accepts this and sets the boundary: the part is good if the size lands between the minimum and maximum limit.

An academic lecture on engineering drawing defines tolerance as the total permissible variation of a size, the difference between the maximum and minimum limits. A dimension of 2.000 ±0.005 in therefore has a tolerance of 0.010 in in total, and any part measuring between 1.995 and 2.005 in passes.

Two points trip up first-time buyers:

  • The ± is half the story. A ±0.005 in tolerance is a 0.010 in window. Some drawings use a bilateral form (±), others a unilateral form such as +0.010/0, where all the variation goes one way.
  • Tighter is not “better.” It is a different level of effort. Each step down in tolerance means slower cutting, more inspection and more rejected parts.

How tolerances appear on a drawing

The same lecture notes describe three ways to show tolerances on a drawing:

  1. Direct tolerancing. The limits sit right on the dimension, for example 1.250 +0.002/-0.000. Use this for the few features where the number matters.
  2. A general tolerance note. One line in the title block, such as “all dimensions held to ±0.05,” covers every dimension without its own limit.
  3. Geometric tolerancing. Special symbols control the shape of a feature, such as flatness, squareness or position, separately from its size.

The Precision Machined Products Association’s designer’s guide recommends a tolerance on each critical dimension plus a tolerance block covering all the others, with decimals preferred over fractions. It also asks designers to state a tolerance for every linear, radial and angular dimension, so nothing is left to interpretation.

For a kitchen or hospitality project, the practical meaning is simple. If you hand a shop a drawing with no title-block tolerance, someone has to guess. That guess is where disputes about a sink cutout, a hood opening or a table leg location start.

Standard CNC tolerances: the baseline to expect

Standard CNC tolerances: the baseline to expect

Shops do not all quote the same numbers, but the ranges are consistent. One published reference chart puts the typical result at about ±0.005 in (±0.13 mm) on a linear dimension from a clean drawing without special effort, and about ±0.001 in (±0.025 mm) when the part is inspected to a precision standard. For turned shaft diameters the same chart lists about ±0.002 in as standard.

These are rules of thumb, not guarantees from any one machine. What a shop can hold depends on the material, the part size, the setup and how the part is measured. Here is how to think about the bands:

Level Typical window Where it fits
General / standard About ±0.005 in (±0.13 mm) Brackets, enclosure panels, cutouts, plates, most visible metalwork
Tighter, inspected About ±0.001 in (±0.025 mm) Mating parts, press fits, precision locating features
Beyond that Specialized finishing and inspection Rare in kitchen and hospitality work

Metric drawings often rely on a general standard instead. ISO 2768-1 sets general tolerance classes called fine, medium, coarse and very coarse, and medium is the most common default. In that standard the allowed variation grows with the size of the feature: a 10 mm dimension is held tighter, in absolute terms, than a 500 mm one.

Why size changes the answer

The University of Florida’s design lab explains that typical achievable tolerances grow with part size. Measuring instruments, machine encoders and the machine itself all carry a positioning error that builds up over longer travel. A long stainless panel or a six-foot table frame cannot be held to the same absolute window as a small bracket, and a good drawing reflects that.

The same handout makes a point buyers rarely hear: its example shows that a 6-inch caliper with an error of about 0.001 in per inch would read a 10-inch dimension as 10.000 ±0.010 in. A ±0.005 in requirement on that dimension could not be checked with that tool. A tolerance only means something if the part can be measured to it.

Process matters: milling, cutting, welding

CNC machining is one family of processes. Metalwork for a commercial kitchen usually combines several, and each one has its own natural accuracy:

  • CNC milling and machining removes material with rotating tools. It is the process for precise pockets, holes, slots and mating surfaces.
  • Fiber laser cutting produces clean profiles in sheet and plate, and suits fine detail, perforations and tight nesting of parts.
  • Plasma cutting is fast on thicker plate and structural parts, where edge finish and the last fraction of an inch are less critical.
  • Water jet cutting cuts without heat, which helps with materials that distort or harden under thermal cutting.
  • Welding joins pieces and adds heat, so assemblies carry their own allowance for movement after the weld.

The lesson for an architect or contractor is to avoid applying a milled-part tolerance to a welded assembly. A machined bearing bore and the overall length of a welded frame are not the same kind of feature. Tolerance the overall frame the way a fabricator can build and check it, and tolerance the machined features separately.

We offer CNC plasma, fiber laser and water jet cutting, milling and welding in-house, which means one team can pick the right process for each feature instead of forcing the whole part through one method.

What counts as a tight tolerance, and when you need one

In general, tight tolerance work starts around ±0.001 in. It is justified on features where two parts meet or a seal has to hold:

  • Bearing seats and bushing bores
  • Locating dowel holes
  • Sealing faces
  • Sliding or rotating parts

It is wasted on bolt clearance holes, cosmetic chamfers, outer edges nobody touches and panels that are trimmed or caulked on site. In a commercial kitchen, a countertop edge, a wall cladding panel or the outside of a hood rarely needs machinist-grade precision. What it needs is the right fit to the wall and to the equipment, plus a clean weld and finish.

Fits and the H7 question

If you review a drawing from an engineer, you may see codes such as “H7” or “H7/g6.” These come from ISO 286, the international system that describes how a hole and a shaft fit together. The standard exists because mass-produced parts must be interchangeable and exact size is unnecessary for most features.

The three fit families are:

  • Clearance fit: the shaft is always smaller than the hole, so it slides or turns freely.
  • Transition fit: the sizes overlap, so the part may be snug or slightly loose. This is used for locating parts.
  • Interference fit: the shaft is always larger than the hole, so the parts are pressed together and stay put.

In the code, the letter gives the position of the tolerance zone and the number gives its width, called the IT grade. A capital H means a hole. H7 holes start at the nominal size and are allowed to run slightly larger. How much larger depends on the diameter. Bossard’s ISO 286-2 tables list H7 fields of +0.010/0 mm for 1 to 3 mm sizes, +0.018/0 mm for 10 to 18 mm and +0.025/0 mm for 30 to 50 mm nominal diameters. A 40 mm H7 hole can therefore measure anywhere from 40.000 to 40.025 mm.

You do not need to calculate any of that yourself. If a drawing for a roller, hinge pin or sliding mechanism calls for H7, the point is simply that the hole has a defined, narrow window and the shaft is sized to match it.

Fits and the H7 question

How to choose tolerances without overpaying

The PMPA guide tells designers to specify tolerances only as close as necessary for part function. That is the single most useful rule for a buyer. Here is how to apply it in five steps.

  1. Start with function. For each dimension, ask what happens if it is off by 0.01 in. If the answer is “nothing,” the general tolerance is enough.
  2. Mark only the critical features. Mating faces, holes that receive pins or fasteners with little clearance, and cutouts that must match equipment dimensions get their own limits. Everything else falls under the title-block note.
  3. Pick a realistic general tolerance. Use the standard window for the process and size. Tightening the whole drawing because a few features matter turns the entire job into a precision job.
  4. Dimension from a common datum. The PMPA guide suggests using one common reference point or plane for all dimensions and asking how each one will be measured, so the drawing is unambiguous.
  5. Confirm the measurement method. A tolerance that the shop cannot verify is not a real requirement, as the 10-inch caliper example above shows.

The same discipline applies well beyond metal. A custom joinery design works the same way: the designer fixes the few measurements where parts must meet precisely and lets the rest follow the practical limits of the build.

Equipment cutouts and site fit

For kitchens the tolerances that cause real trouble are rarely on a machined face. They are the cutout for a sink bowl, the opening for a range hood, the gap between a countertop and a wall, and the spacing of table legs to a floor that is not perfectly level. Provide the equipment spec sheets and site measurements with the drawing. Tolerances then go where the building and the equipment demand them, not where a generic template puts them.

What to send a shop before it quotes

A complete request avoids revisions and surprise charges:

  • A dimensioned drawing or CAD file, with a general tolerance note in the title block
  • Direct tolerances on the few critical features only
  • Material and thickness, and any finish requirement
  • Quantity, because setup cost spreads differently across one piece and one hundred
  • Equipment specs and site measurements for anything that has to fit existing items
  • Which surfaces are visible, so the finish effort goes where people will see it

Perspective

We make custom stainless steel countertops, sinks, exhaust hoods, wall cladding, tables and heavy enclosures for restaurants, hotels and other commercial spaces, all manufactured locally in Brooksville, Florida. With more than 60 years of combined experience on our team, we have learned that most tolerance problems start on paper, not on the machine.

Our approach is to treat the drawing as a conversation. We look at what each dimension has to do, then match the process to it: CNC machining or milling for precise features, fiber laser, plasma or water jet for profiles, and welding for assemblies. Having these capabilities in one facility means a tight feature and a loose one can live on the same part without the whole job being priced as precision work.

We believe the right tolerance is the one your kitchen, your equipment and your installer can actually use. If you are an architect or contractor with a drawing in progress, we would rather help you tighten the three dimensions that matter than quote a precision number on all thirty.

the author

Bring your drawing to Day Metal

If you have a project with specific fit requirements, we can review the drawing, advise on which dimensions need their own limits and manufacture the part in Florida. Our fabrication and welding team handles custom stainless work, and our cutting services cover fiber laser, plasma and shear cutting. Tell us the material, the function and the fit, and we will take it from there.

Day-metal

For an overview of everything we build, from countertops and sinks to exhaust hoods and enclosures, see our main page.

FAQ

What is the standard tolerance for CNC machining?

For general CNC work, about ±0.005 in (±0.13 mm) is a common baseline on a linear dimension. Many shops quote tighter, around ±0.001 in, when a feature is called out and inspected. The exact figure depends on the material, size and setup, so state it on the drawing.

What are the three types of tolerances?

On a drawing, tolerances are shown as direct limits on a dimension, as a general note that covers all unmarked dimensions, or with geometric symbols that control shape and position. Most parts use a mix: a general note for the bulk of the part and direct or geometric tolerances for the critical features.

What does H7 mean?

H7 is an ISO 286 code for a hole. The letter H places the tolerance zone at the nominal size and slightly above it, and the 7 sets the width of the zone. Wider holes get a larger window, so a 40 mm H7 hole can run from 40.000 to 40.025 mm. It is normally paired with a shaft code such as g6 to set a sliding fit.

Do all dimensions on my drawing need tight tolerances?

No. Only features that mate with other parts, seal, locate or slide need them. Edges, clearance holes and cosmetic details can follow the general tolerance. Tightening everything adds machining time, inspection and rejected parts without improving how the piece works.

How do I know a tolerance can be measured?

Ask how the dimension will be checked, especially on large parts. Instrument error builds up over longer distances, so a requirement that is tight relative to the measuring tool cannot be verified. Dimensioning from one datum and keeping tolerances realistic for the part size makes inspection straightforward.

Sources

Have a Project in Mind?

Bring your questions and specifications to the Day Metal team.

Discuss Your Project